1. P1R11FA10 - 001 : Connections
1.1 Informations
Release
This document is fully valid, except for errors or omissions.
| Release | Description | Date |
|---|---|---|
| 1.0 | New manual. | 15/07/16 |
Specifications
All rights reserved on this manual. No part of this document can be copied or reproduced in any form without prior written authorisation .
QEM does not insure or guarantee its contents and explicitly declines all liability related to the guarantee of its suitability for any purpose. The information provided in this document can be changed without notice. QEM shall not be held liable for any error that may appear in this document.
Registered Trademarks:
- QEM® is a registered trademark.
- Microsoft® and MS-DOS® are registered trademarks and Windows® is a trademark of Microsoft Corporation.
1.2 Description
The P1R11FA10 - 001 application, installed on the Qmove C1-R11-FA10 hardware, it is the Modbus/RTU Slave gateway to the QEM HA548.04 instrument.
Follow we report the main features of the P1R11FA10 - 001 software.
1.3 Hardware and connections
1.3.1 Main board
1.3.1.1 Power supply
The instrument will need to be supplied with 24Vdc. Isn't necessary the internal fuse.
1.3.1.2 Connectivity
- PROG PORT → TTL logic standard serial port for programming.
- USER PORT → Multistandard (RS232, RS422, RS485) port for MODBUS/RTU Slave.
- PORTA AUX RS485 → RS485 port for HB548.04 connection.
Nr. 1 MMC card reader for saving/storing from external memory.
1.3.1.3 C1-R11
 |
| C1-R11 front view |
1.4 Electrical connections
1.4.1 C1-R11
1.4.1.1 CN1- Power supply (power input)
| Power supply type | 24 Vdc | 24 Vac |
|---|---|---|
| Valid range | 22 ÷ 27 Vdc | +/-15% |
| Max. absorption | 30W | 35VA |
| Frequency | 50/60Hz |
 | 1 | AC phase / positive DC terminal |
| 2 | Ground | |
| 3 | AC phase / 0V DC terminal |
CN2 - USER PORT. RS232-RS422-RS485 serial (insulated)
 | 1A | A – RS485 MODBUS/RTU Slave |
| 2A | B – RS485 MODBUS/RTU Slave | |
| 3A | 0V - Serial port common. | |
| 4A | 0V - Serial port common. | |
| 5A | TX (Transmission RS232) | |
| 6A | PE - Ground. | |
| 1B | RX - (Receive “positive” RS422) | |
| 2B | RXN - (Receive “negative” RS422) | |
| 3B | TX - (Transmission “positive” RS422) | |
| 4B | TXN - (Transmission “negative” RS422) | |
| 5B | RX (Riceive RS232) | |
| 6B | PE - Ground. |
NB. The DIP SW2 group under the serial port must be set with ONLY THE 5 DIP = ON.
1.4.1.1.1 USER PORT settings
1.4.2 Selettore baud-rate di PROG PORT e USER PORT
| SW1 | Dip | Impostazione dei DIP | Funzione | |||
|---|---|---|---|---|---|---|
 | 1 | OFF | OFF | ON | ON | Selezione velocità di trasmissione PROG PORT |
| 2 | OFF | ON | OFF | ON | ||
| Baud-rate 38400 | Baud-rate 115200 | Baud-rate 19200 | Baud-rate 57600 |
|||
| 3 | OFF | OFF | ON | ON | Selezione velocità di trasmissione USER PORT | |
| 4 | OFF | ON | OFF | ON | ||
| Baud-rate 38400 | Baud-rate 115200 | Baud-rate 19200 | Baud-rate 57600 |
|||
| 5 | Selettore baud-rate CANbus. Vedere paragrafo Selettore baud-rate CANbus | |||||
| 6 | OFF | ON | Selezione modo di funzionamento PROG PORT | |||
| PROG PORT utilizzabile anche dai device SERCOM e MODBUS | PROG PORT non utilizzabile dai device SERCOM e MODBUS | |||||
| 7 | Selettore baud-rate CANbus. Vedere paragrafo Selettore baud-rate CANbus | |||||
| 8 | OFF | ON | Seleziona la USER PORT come PROG PORT1) | |||
| PROG PORT normale | PROG PORT sul connettore della USER PORT | |||||
1.4.3 AUX2 PORT
| CN4 | Morsetto | Simbolo | Descrizione |
|---|---|---|---|
 | 1 | 0V | Comune seriale RS485 |
| 2 | B | Terminale RS485 B - da collegare al pin nr. 2 del DB9-M del HA548.04 | |
| 3 | A | Terminale RS485 A - da collegare al pin nr. 8 del DB9-M del HA548.04 |
| SW4 | Num. Dip | Nome Dip | Impostazione dei DIP | Funzione |
|---|---|---|---|---|
 | 1 | JP3 | ON | Polarizzazione RS485 |
| 2 | JP2 | ON | Terminazione RS485 | |
| 3 | JP1 | ON | Polarizzazione RS485 | |
| 4 | X1) | Nessuna |
Abilitare le Settaggio resistenze di polarizzazione e terminazione AUX2 PORT